hardening相关论文
Innovative Technology and Development in Strength Design and Integrity Assessment of Pressure Vessel
This paper discusses the strength design methods in ASME Boiler and Pressure Vessel(B&PV)Code with a focus on the design......
Pretreatment technology is deeply discussed to explain its importance in guaranteeing properties and formability of alum......
Radiation-induced attenuation (RIA) in four types of polarization-maintaining optical fibers for interfer-ometric fibero......
By using numerical analysis methods to simulate the deep excavation,a lot of analyses are established on the basis of tw......
In this paper,the effects of hardening exponent,yield strength and elastic modulus on the deformability of near hemisphe......
The effect of homogenization on the hardness,tensile properties,electrical conductivity and microstructure of as-cast Al......
The changes in the mechanical behavior of electric resistance welded(ERW) pipes before and after the cage roll forming p......
The residual stress of T-joints for SUS304 stainless steel by YAG laser welding was measured by the method of hole-drill......
Specimens of two different kinds of bake hardening steels(BH-Mn and BH-P) were prepared and treated with different annea......
Vickers hardness change of the Chinese low-activation ferritic/martensitic steel CLF-1irradiated wit
In the present work,the irradiation hardening behavior of a Chinese low-activation ferritic/martensitic steel CLF-1,a ca......
Al-Mg-Si-Cu alloys with and without Zn addition were fabricated by conventional ingot metallurgy method. The microstruct......
Effects of pre-strain and baking parameters on the microstructure and bake-hardening behavior of dua
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生......
In this paper, the characterization of oxygen permeation (OP) in titanium alloy TC11 at high temperature and the influen......
目的：探讨经皮穿刺介入硬化治疗肝囊肿的方法及疗效。方法：37例肝囊肿患者（男12例，女25例），41个囊肿，行B超引导下经皮穿刺肝囊肿内注射无......
On The Enhancement of Wear Resistance of Hardened Carbon Tool Steel (AISI 1095) With Cryogenic Quenc
Many experimental investigations reveal that it is very difficult to have a completely martensitic structure by any hard......
Influence of impact energy on work hardening ability of austenitic manganese steel and its mechanism
To further understand the hardening mechanism of austenitic manganese steel under actual working conditions,the work har......
目的：探讨急诊内镜下硬化剂注射及组织黏合剂栓塞治疗食管胃静脉曲张破裂出血的临床效果。方法回顾性分析52例食管胃静脉曲张破裂出......
Viscoelasto-plastic rheological experiment under circular increment step load and unload and nonline
...
Effects of pre-strain and baking parameters on the microstructure and bake-hardening behavior of dua
In a typical process, C-Mn steel was annealed at 800°C for 180 s, and then cooled rapidly to obtain the ferrite-martens......
In a typical process,low carbon steel was annealed at two different temperatures(660℃ and 750℃),and then was temper ro......
研究不同的析出硬化和冷加工组合对6061铝合金拉伸性能的影响.结果表明,在不同的热处理过程中,在180℃单时效4 h能提高合金的强度......
The epoxy resin polymer cement mortars with excellent performances were made up through modifying ordinary Portland ceme......
